Tag Archives: ptfe tape

hot-sale-products

Fire Protection – Tape-Dope Pipe Sealant Comparison

Fire Protection – Tape-Dope Pipe Sealant Comparisonhot-sale-products

Leaking sprinkler systems can cause tens of thousands of dollars in damage to ceilings, floors, furnishing and other valuables. Preventing these leaks is not an option for installers, it is a requirement. The metal pipe connections in sprinkler systems can be sealed with PTFE tape, pipe dope or anaerobic sealant; the choice of products is dependent on the application.

Sprinkler systems that are composed of metal pipe have two primary causes for leaks. The leaks in the connections of metal pipe as well as the pin hole leaks in the welds. Pin hole leaks can be prevented or eliminated by heating the pipe and coating with an anaerobic weld sealant.

Preventing leaks in the connections and fittings of the pipe can be done with PTFE tape, pipe dope or anaerobic sealant.

PTFE Tape

PTFE tape can seal connections, if the pipe is not directional. Tightening of the pipe must be done to the proper torque. If the pipe is over tightened or must be loosened to change the direction of the pipe the seal is no longer In other words if it is at the user discretion when to stop tightening. PTFE tape is not recommended on nicked or damaged threads.

Pipe Dope

Pipe Dope, a solvent based adhesive, remains a paste. It provides a good seal but does not prevent loosening due to vibration or stress. Pipes that change temperature frequently or are near equipment or other sources of vibration may loosen over time.

Anaerobic Sealant

Anaerobic sealants cure to form a plastic seal. They cure only when in contact with metal and removed from oxygen. This makes them easy to work with and clean up. Many contain PTFE which eases assembly.

Anaerobic pipe sealants provide an instant seal of up to 1000psi and when cured can exceed the burst rating of the pipe. The cure does not happen instantly so if pipes must be realigned within the system to square off the lines, readjusting will not disrupt the seal. The high viscosity material provides seals on nicked or damaged threads.

Should it ever be necessary to disassemble a sprinkler system sealed with anaerobic sealants normal hand tools will do the job. Anaerobic sealants provide inherent corrosion prevention so there are no rusted connections to deal with.
Traditional Anaerobic sealants should not be used on CPVC (plastic) pipe, however, anaerobic pipe sealants have been developed for use on metal pipe work in systems that may also contain CPVC.

high-temperature-resistance-jumbo-roll-ptfe-thread-seal-tape

About thread seal tape

About thread seal tape

high-temperature-resistance-jumbo-roll-ptfe-thread-seal-tape

Thread seal tape (also known as PTFE tape or plumber’s tape) is polytetrafluoroethylene (PTFE) film for use in sealing pipe threads. The tape is sold cut to specific widths and wound on a spool, making it easy to wind around pipe threads. It is also known by the genericised trade-name Teflon tape; while Teflon is in fact identical to PTFE, DuPont (the trade-mark holders) consider this usage incorrect, especially as they no longer manufacture Teflon in tape form.Thread seal tape lubricates allowing for a deeper seating of the threads, and it helps prevent the threads from seizing when being unscrewed.The tape also works as a deformable filler and thread lubricant, helping to seal the joint without hardening or making it more difficult to tighten,and instead making it easier to tighten.

Typically the tape is wrapped around a pipe’s thread three times before it is screwed into place. It is commonly used commercially in applications including pressurized water systems, central heating systems, and air compression equipment.

Thread tape is appropriate for use on tapered threads, where the sealing force is a wedge action. Parallel threads may not seal effectively with or without tape, as they are intended to be sealed by a gasket.

Thread sealing tape is almost entirely applied by hand, although at least one machine is available for production wrapping of fittings.

PTFE tape is also commonly used in the stretching of body piercings, through a process known as taping, because it is inert and safe for this use. The wearer wraps layers of the tape around a plug, slowly increasing the size and thus slowly increasing the size (gauge) of the piercing.

Overuse or misapplication of thread tape may be a hazard. Excess application of PTFE tape can prevent mating threads from fully engaging, reducing the shear point of the threads. Combining thread-seal tape with a pipe dope compound can also overload threads. Also, internal overhangs of loose material may constrict a joint or slough off and form a foreign body that could jam a valve seat. Therefore, use of PTFE tape as a thread sealant is generally not considered appropriate in fluid power (hydraulic) systems.

Fire protection – tape-dope pipe sealant comparison

Fire protection – tape-dope pipe sealant comparison

Leaking sprinkler systems can cause thousands of dollars in damage to ceilings, floors, furniture and other valuables. Prevent leakage of these options are not installed, which is a requirement. Metal pipe connection automatic sprinkler system can be used PTFE tape, pipe dope or anaerobic sealant; product selection is application dependent.

These are two main reasons from a metal pipe sprinkler system leakage. Leak metal pipe connections, and pinhole leaks in the weld. Pin hole leak can be prevented or managed by the anaerobic welding and coating and sealant is heated to eliminate.

In connection with pipe joints can prevent leakage of PTFE tape, paint or anaerobic pipe sealant to.

PTFE tape

PTFE tape to seal the connection, if the pipe is not directional. Tighten the pipe must make the appropriate tightening torque. If the pipe is too tight or tube must be loosened to change the direction of the seal is no longer in other words, if it is at the discretion of the user when to stop tightening. Not recommended cracked or damaged threads PTFE tape.

Pipe dope

Pipe coatings, solvent-based adhesives, maintaining paste. It provides a good seal, but does not prevent loosening due to vibration or stresses. Frequent changes in temperature or near equipment or piping vibration from other sources may loosen over time.

Anaerobic sealant

Anaerobic sealant cured to form a plastic seal. They only treatment and removal of oxygen upon contact with the metal. This makes them easy to use and clean. Many comprising polytetrafluoroethylene, thereby simplifying the assembly.

Anaerobic pipe sealant to seal the moment offered to 1000PSI and when the pipe burst may exceed the level cure. Therefore, if the pipe system must be readjusted in the square break, adjustment will not break the seal of curing does not occur immediately. High-viscosity materials provided thread sealing cracked or damaged.

It should never be necessary removal and anaerobic sealing sealing normal hand tools will do the job sprinkler system. Anaerobic sealants provide inherent corrosion, so there is no connection to deal with rust.
Traditional Anaerobic sealants should not be used (plastic) in the CPVC pipe, however, anaerobic pipe sealant has been in the metal pipe may contain on CPVC systems developed for use at work.

Fittings for waster systems

Fittings for waster systems

Tube
Choose from different plastics, including ABS. Polypropylene and PVC. Support approximately every 500 mm horizontal tube. Approximately every 12 meters vertical pipe. Connected to a single system stack pipe bowl is limited to a maximum length of 3μm, unless special precautions (special automatic resealing trap design or with a separate ventilation duct systems, for example).
Flexible sewer basins and sinks are being provided particularly useful.
Sockets
For joining the plain end pipe lengths together. The method can be used for all connections. Some socket has a blunt end to take another connector instead of the pipe.
Elbow
For to see around corners “horizontal” pipe runs. 90 degrees and 135 degrees curved section is the most widely used. Garbage pipe should slope (but often just a little) toward the exit – will be connected to a vertical pipe with a 91 degree or 92 degree bend them. Some have blunt ends adjustable bending – rotating – bending are also available.
T-Shirt
Common angles are 90,91,92 and 135 degrees. Tee generally sweep (in the T-shaped member should be assembled so that branched from the main pipe to the bending direction is the same direction of flow of water) in the flow direction. Avoid using links to connect two sewage pipes run in a single stack system wastes should be connected individually to the stack.
Connector
It can be used for various types of pipes connected to different connectors. Reducer can be used to engage 32 mm or 40 mm tube 40 mm or 50 mm tube. Copper compression can be used to connect plastic pipe to existing copper wastes. BSP screwed thread can be used to connect the tube to the waste outlet in the sink and so on. It can not be used in solder paste threads, but PTFE tape may be used as needed.
WC connector
WC make a simple joint is a common end connector. This should be dry-jointed to the WC outlet, use a rubber gasket. Connectors various modes can have a different angle and length of sliding plug (depending on the location of toilets and sewage pipes to be connected). For particularly awkward joints, multi-KWIK connector can be used – again, a variety of patterns avail¬able, including a slight displacement cope with the pan outlet and the sewage pipe.
Trap
P traps have a horizontal outlet; S- trap has a vertical outlet. BSP threaded inlet traps usually have a direct connection to the waste outlets. Traps can light seal waste discharged into ditches or hopper head use; traps should be used in a single stack systems deep seal (75 mm). Deep seal traps take up more space, and you may need to install a cut under the floor bath. Bottle trap those tidy than the tube, may be easier to use in tight spaces, rather than deep seal trap – they should not be used in the waste. Bath traps often to complete the connection over¬flow system. Washing machine washing machine has a trap to take the side of the outlet hose import – replacing the sink trap trap. In some cases, automatically re-seal closure may be necessary – for example, for connection to a single stack system long basin waste.

What is plastic fabrication

What is plastic fabrication

Plastic guidance on how
The first man-made plastic was named Parkensine Alexander Parkes invented in 1862, it is a cellulose-based plastic.
Bakelite was the first fully synthetic plastic which is manufactured in 1907, chemist Leo Baekeland in New York. This is called a phenolic resin. The earliest plastics.
bakelite
A term often used to describe a hard, dense, plastic laminated by applying heat and pressure to the material with a variety of synthetic resin impregnated paper, or a glass cloth made of cotton fabric layers. These materials have good mechanical strength and dimensional stability and excellent dielectric properties. Used in various fields such as the electrical junction box, aircraft cable pulleys, bearings, gears and transformers
AVALABLE: From 0.8 mm table – 100mm thick. Rhodes with a 4mm tube.
Since then, many other plastics have been invented or discovered. Typically, these are:
nylon:
Currently the most widely used engineering thermoplastics. Manufacturing engineering in several grades, mainly type 6 and 66 are the most common type in the entire 6 toughness, the perfect combination of mechanical strength and impact resistance. Glass filled with black, molybdenum disulfide, graphite and special lubricating grades are also available. For technical components, bushings, bearings, gears, wear pads, rollers, pulleys, etc.
Language: From 0.5 mm tables – in different sizes 100mm thick. Rhodes from 5mm – 500 meters. Tubes are typically administered to order.
PVC:
Non-corrosive, chemical and oil. PVC has excellent electrical insulating properties and is self-extinguishing. Electronic components, laboratory equipment, photographic and chemical tanks, hood, etc. for easy to cut, shape, welding and fabrication. The highest temperature of 60 ℃.
Language: plate from 1.5mm – 70 mm thick. Rhodes from 6–200 mm.
Polyethylene:
HDPE: High-density Polyethlenes is a broad chemical resistance. They have excellent insulation properties, virtually no moisture absorption and maintain their properties even at low temperatures. HDPE is an ideal cutting board food processing sector. In the most commonly used engineering grade UHMWPE and HMWPE.
UHMWPE: ultra-high molecular weight polyethylene having the highest impact strength and wear resistance of any thermoplastic of the best today. Widespread use of self-lubricating, wear strips over the food and packaging industry guide, roll, blade, star wheel, feed insects, chute liners, etc.
HMWPE: ultra-high molecular weight polyethylene prices generally provides a good compromise engineering and property. Used in many similar applications to ultra high molecular weight polyethylene, but abrasion resistance is not critical.
Language: From 1.0 mm variety of plates – 100mm thick natural, black and green. Rhodes 10 -250mm.
Polycarbonate:
Almost unbreakable.
Currently known toughest glass material, the impact strength of polycarbonate greater than or equal to 250 times the thickness of the glass. Mainly used for a variety of security, anti-sabotage and anti-theft windows. Some common uses include machine shields, protective window cranes and forklifts, safety masks, riot shields, etc. for schools, bus shelters, factories and buildings, stadiums and other glazing
Languages: table from 1mm to 12mm thick. Rods & Tubes are also available.
Acrylic:
Commonly known as Perspex®, acrylic glass in many areas ideal substitute. It is widely used in signage, lighting, safety glass, machine guards, meter cover, a display unit, windows airplanes, boats and caravans, glass cab tractors and other machinery. Acrylic with high-definition excellent weathering capabilities. Less than half the weight of glass, but reached 15 times more resistant to breakage.
Language: From 1.5mm to 50mm thick plates of various sizes and colors. Applicable to signs and light boxes, prism cover and opal acrylic skylights. Clear lever up 150mm. Tube forms the outer diameter of the outer diameter of 6mm to 500mm.
TEFLON:
Provide first-class performance.
Commonly known as TEFLON®. PTFE has preferably any plastic chemical resistance. Very high heat resistance, very good electrical properties of low friction coefficient makes it unique combination of materials. For the bearing pads, washers, packing rings, insulators, and many chemical equipment parts. And also glass fibers, carbon or bronze fillers to improve the mechanical properties produced.
Language: a variety of plates, rods and tubes, polytetrafluoroethylene turning belt, plain and etching. Teflon coated glass cloth can also be used for heat sealing applications.
These are only a few in a variety of general-purpose plastics in our modern applications.
Plastic has developed a long way, and now many of our factories machine guards of polycarbonate around the world.
Acrylic is the case almost every shop to use as a display booth, light boxes, cake stand, point of sale displays, and so on.
Including food-grade polyethylene grades in various fields of engineering in many ways, using now. Ultra-high molecular weight polyethylene having a high co-efficient of friction espcecially and excellent wear characteristics.
Acetal is widely used with excellent dimensional stability and good creep resistance precision machined parts.
Polypropylene is mainly used in the manufacture of chemical tanks, because it has excellent chemical resistance.
POINT sale display stand:
Acrylic is widely used in point of sale displays, because it is easy to manufacture and use of hydrogen and oxygen flame once, it looks like polished glass.
With the use of a special solvent manufacturer is able to achieve the manufacturing museum display needs to be done.
CNC router
Most of today’s material can be CNC machining.
Common plastic, CNC routing may be:
Acrylic 2 meters per / minute
Polycarbonate 2.5 meters per / minute
Polyurethane uses helical milling using multi-path selection and routing of 1.8 meters per / minute
Yuan / min 4.0 m – 3.5 HDPE route
PVC 2.5 meters per / minute
Nylon is tough route depending on the thickness yuan / min, usually 2 meters.

Fire protection – tape-dope pipe sealant comparison

Fire protection – tape-dope pipe sealant comparison

high temperature resistance jumbo roll ptfe thread seal tape

Leaking sprinkler systems can cause thousands of dollars in damage to ceilings, floors, furniture and other valuables. Prevent leakage of these options are not installed, which is a requirement. Metal pipe connection automatic sprinkler system can be used PTFE tape, pipe dope or anaerobic sealant; product selection is application dependent.

These are two main reasons from a metal pipe sprinkler system leakage. Leak metal pipe connections, and pinhole leaks in the weld. Pin hole leak can be prevented or managed by the anaerobic welding and coating and sealant is heated to eliminate.

In connection with pipe joints can prevent leakage of PTFE tape, paint or anaerobic pipe sealant to.

PTFE tape

PTFE tape to seal the connection, if the pipe is not directional. Tighten the pipe must make the appropriate tightening torque. If the pipe is too tight or tube must be loosened to change the direction of the seal is no longer in other words, if it is at the discretion of the user when to stop tightening. Not recommended cracked or damaged threads PTFE tape.

Pipe dope

Pipe coatings, solvent-based adhesives, maintaining paste. It provides a good seal, but does not prevent loosening due to vibration or stresses. Frequent changes in temperature or near equipment or piping vibration from other sources may loosen over time.

Anaerobic sealant

Anaerobic sealant cured to form a plastic seal. They only treatment and removal of oxygen upon contact with the metal. This makes them easy to use and clean. Many comprising polytetrafluoroethylene, thereby simplifying the assembly.

Anaerobic pipe sealant to seal the moment offered to 1000PSI and when the pipe burst may exceed the level cure. Therefore, if the pipe system must be readjusted in the square break, adjustment will not break the seal of curing does not occur immediately. High-viscosity materials provided thread sealing cracked or damaged.

It should never be necessary removal and anaerobic sealing sealing normal hand tools will do the job sprinkler system. Anaerobic sealants provide inherent corrosion, so there is no connection to deal with rust.
Traditional Anaerobic sealants should not be used (plastic) in the CPVC pipe, however, anaerobic pipe sealant has been in the metal pipe may contain on CPVC systems developed for use at work.

PTFE sheets: a commodity with numerous applications

PTFE sheets: a commodity with numerous applications

Engineers need many things, while creating and discover a variety of objects. Significant changes in key material called PTFE engineering plastics have been invented seventy years ago, and even today, it is seen as the better known properties. There are many types of engineering plastics market. However, PTFE film is most useful in the great cause of the industry, you can also learn a related plastics, is truly effective special attributes.

Advantages PTFE plate

Resulting in low friction – .. feature PTFE is so effective, it has a low coefficient of friction which is known as the lowest of all the material, which is present in the earth as a more specific facts, it is just one such ice there is in the market PTFE tape numerous applications, you can easily find their way from the online search engine.

Chemical resistance -… it is another wonderful feature of PTFE. It has amazing power chemical resistance compared to other plastics in the market, it has a high resistance, and the plastic is involved in a joint application and use, you will not find any chemical .. that can damage plastic sheets having a PTFE acid-resistant features, because, in the plastic sheet can easily withstand the acidic reaction higher concentrated acid; it can use in many ways.

High temperature -… PTFE sheet also requires a high temperature since the material can easily withstand low temperatures, it will retain the same level of performance will have no impact on the quality of the material, even if the temperature exceeds 250 degrees Celsius, which will work in a wonderful way, without affecting its performance can resist temperature can even be reduced to a level – 260 ℃. It is basically effective use of the interior of the container liner.

Electrical insulation – It is PTFE tape, is considered to be the best material for electrical insulation which is also used for another important characteristic in an effective manner, such as PVC, one of the wonderful substitute.

PTFE Application

People can now find a variety of use of the device, which is used in the food production industry, the reason for it to use it is due to the fact that it is really safe and will not contaminate food particles at all in the food industry. It is truly safe food use, because it does not have any harmful effects. This particular variety of engineering plastics in the construction industry has a great many uses, even modern architects have realized that resistance effect on weather conditions, even if environmental change such as engineering plastics, which is a wonderful variety does not have the environment any negative impact of changes, which is used in industrial products, cost reduction, because it also has a super slide variance, industrialists are interested in these products. PTFE tube has also been used to obtain a successful industrial applications.

What types of tape products are available?

What types of tape products are available?

The term tape products cover a lot of different types of products, of which there are many different uses. This is about a small fraction of the various types of information which can be used to use some tape products.

Duct tape
Tape is a very popular is known for its strength and its versatility with type. Its adhesive qualities for a long period of time, they are able to resist weathering zone. It can be used in industrial maintenance, it is generally considered as a lot of different problems, a quick fix.

Teflon tape
Teflon tape or called polytetrafluoroethylene. It is used in many industries, such as pipeline around the pipe, it can help to make a few different functions easier to perform wound. It can be used as a filler, thread lubricant, or easy to tighten the joint approach.

Reflective tape
Reflective tape light is reflected back toward the source. This is a good choice if you need to mark out something that is dangerous, or more likely to be found in dark conditions. It can be used in clothing or in solid objects, depending on whether it is needed.

Magnetic tape
Tape attract certain types of metal with it, or may be glued to the other tape. It is often used for materials that need to be held together, but it should be only loosely held together. It can be easily opened.

Carpet tape
Carpet tape is a substance often carpet fitter. It can be used to help keep the carpet in place, or honest carpet rough edges, so it looks neat when it is in place. It is usually double-sided, so that it may be formed with a particularly strong bond between the carpet and the rear floor. This will prevent the carpet slide around and put people at risk.

Glow Tape
Glow in the dark with the lights stay lit once closed. It can be used to help people see things in the dark signs of danger. It is often used to draw people’s attention to things, which might need to be visible, regardless of light conditions.

If you are unsure what type of tape products, you may need, you can always use professional exchanges tape products, they can help you find the right person.

Tips on how to stretch ears using tape

Tips on how to stretch ears using tape

Earlobe stretching tend to make about your individual design and stunning style statement, but found taper Normally, when you reach a certain size of the challenge. Stretching earlobes generally achieve the 2-3 long tapered to gradually increase the size of the perforation. Cone lubrication and pierces the current stretch, then use a new bigger a rapidly substituted. In general, the maximum size of the taper would be obtained in a. “Style are usually more expensive and difficult to obtain. Pull projecting ears using tape, referred to as” bandage provides “a much cheaper and readily available substitute .

Items you need:

* Plug-in or meat tunnel
* PTFE tape
* Water-based lubricant (optional)

1. Clean your hands, you perforations and plugs, flesh tunnels, and you want to use. Mild, unfragranced cleaning soap or detergent should be used to prevent perforation of irritability.

2. Place 1 layer of tape and wrap-around or flesh tunnel plug the middle. Make sure both sides of the flat ribbon affixed jewelry.

3. Re-insert the jewelry. For those who have difficulties to go back to use the right amount of lubrication.

4. Allow to rest a day or two after the piercing, the replication process, adding an additional layer of tape. Continue adding the tape, a layer of time, every few days, until you achieve your preferred specifications.

prompt:

PTFE tape may be obtained at most hardware stores. If you prefer, you can use the straps as well. Bondage tape can be found online or in the adult business.

Before you can always make time to add more piercing layers of tape to rest. Adding one or more layers of tape, every day is not recommended, because the stretch too quickly can cause injury.

The characteristics of ptfe tape

The characteristics of ptfe tape

The ptfe tape has more characteristics,such as:
1. Compatible with a wide range of gas and liquid.
2. Compatible with a wide range of piping material.
3. It does not harden or crack joint.
4. No curing time.
5. Over a wide temperature range effective.
6. As a thread lubricant and anti-lock.
7. Prevent electrolytic corrosion Thread.
8. Clean.
9. Non-flammable.
10. Unlimited shelf life.

More ptfe tape pictures to show you:

high temperature resistance jumbo roll ptfe thread seal tape

hot sale products

How to use teflon tape

How to use teflon tape

Teflon tape is a metal and plastic pipe threaded ends used to wrap to prevent the leakage of lubricating pipe threads and place to participate in a very thin white tape. Male and female pipe thread ribbon stop filling the tiny gap between leaking. Another method is to use a pipe adhesive bonded materials, which is also sealed and lubricated, allowing tighter engagement. There is also another variety of sealing strip is yellow. Yellow tape is heavy, is a gas line connection. Do not use ordinary gas connection, white, Teflon tape.

If you would like more information about the ptfe tape, you can click on: ptfe tape. Here there is more information you need to know.

Ptfe tape picture products:

20-year ptfe tape manufacturer ptfe sealant rollhot sale products

 

Style of PTFE tape

Style of PTFE tape

Seal used in pipeline applications is the most common white, but it is also a different color available. White Teflon is a single density, yellow and pink triple double. In the UK, the tape is from colored reel, reel such as natural gas for yellow, green for the drinking water.

  • White – for up to 3/8 inch NPT thread
  • Yellow – for NPT thread 1/2 inch to 2 inches, often labeled “air band”
  • Pink – for NPT thread 1/2 inch to 2 inches
  • Green – oxygen line and a number of specific medical gas oil free PTFE
  • Copper – containing copper particles and is certified as a lubricant instead of thread-sealing machine

Our company produces a variety of new PTFE tape,if you are interested in PTFE tape, you can click on:PTFE tape.

PTFE tape products display:

white plumbers sealing tape ptfe
white plumbers sealing tape ptfe
19mm high demand gas pipe seal
19mm high demand gas pipe seal